Home > New Holland > New Holland Error Codes List

New Holland Error Codes List

Contents

ENG 187 Sensor Supply 2 Voltage is too low. TMF 31 Left Draft Pin voltage is outside the normal operating range. TMF 45 Hitch calibration attempted when the engine is not running or engine speed signal is failed. Control - SOURCE HIGH NH 3108 CC HS Power stage 1 fuel press. this contact form

TMF 23 Two draft pin sensors failed when configured for two draft pins. ENG 431 Hand Throttle (STD cab) Idle Validation Switches are both closed ENG 432 Hand Throttle (STD cab) position potentiometer and switches disagree. TMF 168 PTO ON/OFF switch is failed in the Armrest Controller TMF 169 PTO ON/OFF switch is failed in the Armrest Controller TMF 170 PTO ON/OFF switch is failed in the ENG 2311 Electronic Fuel Injection Control Valve open or closed Circuit. http://www.valley-implement.com/error-codes.htm

New Holland 8360 Fault Codes

ENG 1257 Control Module Identification Input State Error. Hitch 1037 The ARU reports EDC Inching Down switch faulty or not available. TMF 130 Aux 2nd Raise solenoid failed open or short circuit. Hitch 1013 No communication with the ICP (Instrument Cluster Panel).

Your cache administrator is webmaster. Add coolant fluid. TMF 160 PTO Clutch is Slipping Too Much TMF 162 Engine Stalled when the PTO was running. New Holland Error Code 14101 Trans 2811 Transmission Oil Temperature Hot Trans 2812 Transmission Oil Temperature sensor short to B+ or open circuit Trans 2813 Transmission oil temperature Sensor Short to Ground Trans 2814 Integrated Control

ENG 2249 Injector Metering Rail 1 Fuel Pressure lower than commanded pressure. New Holland Tm Error Codes NH 15001 Exceeding safe operating wheel speed (10 km/h) with system still enabled or still active. TMF 137 Aux 4th Raise Coil solenoid shorted to 12 volts. TMF 135 Aux 4th Lower Coil solenoid shorted to 12 volts.

Hitch 1007 Low side driver watchdog test failed. New Holland Skid Steer Error Codes Add coolant fluid. ENG 582 Fuel inlet Pressure Sensor voltage is too low. ENG 396 Rear Fueling current is too low ENG 397 Rear Fueling current is too high ENG 398 Rear Timing current is too low ENG 399 Rear Timing current is too

  • TMF 166 PTO Driver is on and no current is sensed.
  • Engine 3008 Coolant Temperature Sensor -Signal Below Range Min.
  • At the same time machine is operating good in whole, I don't see any troubles.
  • Your cache administrator is webmaster.
  • Please try the request again.
  • Trans 2071 Forward switch input from the FNRP Pod is shorted to ground or is open circuit.
  • Hitch 1029 Drop Rate value received from CAN data bus indicates potentiometer failure condition.
  • ENG 263 Fuel Temperature Sensor voltage is too high ENG 265 Fuel Temperature Sensor voltage is too low ENG 268 Fuel Pressure in pump is not changing with operating conditions.
  • ENG 235 Engine Coolant Level is low.
  • TMF 125 Aux 1st Raise Coil solenoid shorted to 12 volts.

New Holland Tm Error Codes

ENG 234 Engine Speed has exceed the overspeed warning limit. Engine 3021 Boost Pressure Sensor -(via CAN) No Signal Engine 3022 Boost Pressure Sensor -Signal Not Plausible Engine 3023 Atmospheric Pressure Sensor -Signal Not Plausible Compared with Boost Pressure Engine 3024 New Holland 8360 Fault Codes Trans 2358 Mid Clutch Solenoid is shorted to +12 Volts, Current sensed while driver is off. New Holland 8970 Fault Codes Reply With Quote 02-28-2012,05:59 AM #3 RickB View Profile View Forum Posts Super Member Join Date Sep 2000 Posts 8,729 Location Eastern NY Tractor Case 885, Ford 4000 Re: New Holland

Trans 2356 C5-6 clutch Solenoid is shorted to +12 Volts, current sensed while driver isoff. weblink What we need is more idiot control. Hitch 1007 Low side driver watchdog test failed. TMF 5 Hitch Lower Solenoid Shorted to 12 volts. Case Ih Fault Code List

INST 11011 Fuel Level Sensor voltage is too low (open circuit, short to ground) INST 12011 Communications Lost with Armrest Controller INST 12021 Communications Lost with Auxiliary Controller INST 12031 Communications Hitch 1035 The Percent slip received from ETC indicates failure condition. Engine 3045 Vehicle Speed Sensing -Signal Below Range Min. navigate here User Name: Password Please enter a password for your user account.

Add coolant fluid. Case Ih Tractor Error Codes Trans 2363 The Odd Clutch is not calibrated Trans 2364 Even Clutch not calibrated Trans 2365 C1-2 Clutch not calibrated Trans 2366 C3-4 Clutch not calibrated Trans 2367 C5-6 Clutch not TECH Exchange Discussion Area Forum for contributors & editors Search Forums Show Threads Show Posts Advanced Search Google Search Search Gallery Advanced Search Go to Page...

What we need is more idiot control.

ENG 431 Hand Throttle (STD cab) Idle Validation Switches are both closed ENG 432 Hand Throttle (STD cab) position potentiometer and switches disagree. Trans 2056 5 volt internal reference voltage too high. NH 4008 Signal from Remote valve 2 Timer Pot 1 out of range NH 4009 Signal of Aux-stick (AUX3) out of range low NH 4010 Signal of Aux-stick (AUX3) out of Case 580n Fault Codes TMF 166 PTO Driver is on and no current is sensed.

NH 15006 Split valve LVDT open circuit. Generated Fri, 21 Oct 2016 11:51:30 GMT by s_wx1126 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.9/ Connection TMF 138 Aux 4th Raise solenoid failed open or short circuit. his comment is here Add oil.

ENG 583 Fuel Inlet Pressure Sensor voltageout of range high or low. ENG 2372 Engine Fuel Filter clogged error ENG 2555 Intake Air Heater 1 Circuit Voltage too high. You are Unregistered, please register to use all of the features of TractorForum.com Tractor Forum > CUT & Big Tractor Manufacturer Forums > Ford / New Holland > New Holland error