Home > New Holland > New Holland Error Code List

New Holland Error Code List

Contents

TMF 141 Aux 5th Raise Coil solenoid shorted to 12 volts. ENG 2322 Engine Camshaft Speed / Position Sensor data invalid. Engine 3021 Boost Pressure Sensor -(via CAN) No Signal Engine 3022 Boost Pressure Sensor -Signal Not Plausible Engine 3023 Atmospheric Pressure Sensor -Signal Not Plausible Compared with Boost Pressure Engine 3024 Furthermore in case you are wondering what I am referring to, here is the link to where you can buy the CD from:New Holland Service Manual CD The error codes and http://windowsazure4j.org/new-holland/new-holland-error-codes-list.html

ENG 1257 Control Module Identification Input State Error. TMF 166 PTO Driver is on and no current is sensed. Trans 2358 Mid Clutch Solenoid is shorted to +12 Volts, Current sensed while driver is off. Engine 3128 Hand Throttle -Channel Difference Error Engine 3129 Hand Throttle -Idle Switch Closed Circuit Engine 3130 Hand Throttle -Idle Switch Open Circuit Engine 3131 Grid Heater Always Switched On Engine http://www.valley-implement.com/error-codes.htm

New Holland 8360 Fault Codes

ENG 2293 Fuel Inlet Meter Device flow demand lower than expected. TRANS 74 The park brake ON with gear is engaged - no park brake request from calibration. TMF 126 Aux 1st Raise solenoid failed open or short circuit. TMF 163 PTO Shaft rotation is detected when the PTO clutch is OFF.

  • ENG 2293 Fuel Inlet Meter Device flow demand lower than expected.
  • NH 4194 Motor mode No.1 switch faulty NH 4195 Motor mode No.2 switch faulty NH 4196 Motor mode No.3 switch faulty NH 4197 Motor mode No. 4 switch faulty NH 5001
  • C TRANS 73 Software is out of the calibration mode and the park brake request is still active.
  • ENG 435 Oil Pressure data invalid ENG 441 Battery Voltage is too Low (less than 6 volts) ENG 442 Battery Voltage is too High ENG 443 Decelerator or Hand Throttle (STD
  • ENG 1257 Control Module Identification Input State Error.
  • INST 3010 PTO Shaft Speed sensor is failed in PTO Controller INST 3020 Engine Speed sensor is failed in the Engine Controller INST 3022 Engine Overspeed Error INST 5010 Engine Oil
  • If this fault is detected there is a bug in the software Trans 2900 Torque sensor Gap is on the larger end of the tolerance (CCH Only) Trans 2901 Signal received

TRANS 76 Engine speed from Eninge Controller does not match the speed signal from the alternator. Power Shuttle faults are listed in neumerical order in the transmission section of the service manual with the troubleshooting flow chart and electrical connector callouts immediately following each listing. ENG 547 Fuel Pressure sensor voltage is too low. New Holland Error Code 14101 Engine 3008 Coolant Temperature Sensor -Signal Below Range Min.

ENG 298 OEM Pressure Sensor Voltage is too low. New Holland Tm Error Codes ENG 2265 Electric Lift Pump for Engine Fuel Supply Voltage too high. Engine 3019 Boost Pressure Sensor -Signal Above Range Max. http://truck-manuals.jimdo.com/new-holland-fault-codes/ TMF 6 Hitch Lower Solenoid High Side Driver circuit short to 12 volts.

TMF 174 Current flowing in the PTO sense resistor when the high side is off. New Holland Skid Steer Error Codes Hitch 1025 Up/Down/Down Momentary switch value received from CAN data bus indicates switch failure. INST 1034 Hydraulic oil filter switch shorted to ground on power up. ENG 299 Engine Shutdown by other than keyswitch (i.e.

New Holland Tm Error Codes

Cycle the shuttle lever which may free up stuck switches, or try driving the opposite direction. http://www.tractorbynet.com/forums/new-holland-owning-operating/233938-new-holland-error-codes.html The time now is 05:42 AM. New Holland 8360 Fault Codes Hitch 1022 Single draft pin sensor failed when configured for one draft pin sensor.(CCH Only) Hitch 1023 Two draft pin sensors failed when configured for two draft pins.(CCH Only) Hitch 1024 Case Ih Fault Code List via data bus command) ENG 319 Real Time Clock in controller has lost power ENG 328 Rear Pumping element is failed ENG 329 CAPS Pump has an overpumping failure ENG 338

Error Code 1 - Transmission oil sensor fault. weblink TMF 123 Aux 1st Lower Coil solenoid shorted to 12 volts. TMF 47 Raise Valve calibration value is too high. (valve problem) TMF 48 Raise Valve calibration value is too low. (valve problem) TMF 50 Hitch position at top of travel is ENG 429 Water in Fuel Sensor voltage is too low. New Holland 8970 Fault Codes

ENG 2322 Engine Camshaft Speed / Position Sensor data invalid. Error Code 2 - Engine coolant sensor fault. Engine 3274 Fuel Low Pressure Sensor Dynamic Plausibility Test -Above Map Engine 3275 Fuel Low Pressure Sensor Dynamic Plausibility Test -Below Map Engine 3276 MIL Visualization Not Available for BC2EDC1 Engine navigate here If this fault is detected there is a bug in the software Trans 2874 The park brakes commanded on and gear is engaged and there is no park brake request from

ENG 263 Fuel Temperature Sensor voltage is too high ENG 265 Fuel Temperature Sensor voltage is too low ENG 268 Fuel Pressure in pump is not changing with operating conditions. Case Ih Tractor Error Codes Engine 3025 Atmospheric Pressure Sensor -Signal Below Range Min. Hitch 1006 EDC Low Side Driver stuck on failure.

Transmission Control Module (TCM)by Nayyar Mahmood13-Automotive Drive Trainsby AmeenMadam Erumby Saad ArifAuto Trans Overhaul (F3A21 & F3A22)by Sam LiSimilar to newholland-feilkoder246015692 FORD New Holland 8670 8770 8870 8970 WSMNew HollandCase New

TMF 137 Aux 4th Raise Coil solenoid shorted to 12 volts. Trans 2343 Clutch Even solenoid open circuit or short to ground.C33 Trans 2344 Clutch C1-2 solenoid open circuit or short to ground. ENG 451 Fuel Pressure Sensor voltage is too high ENG 452 Fuel Pressure Sensor voltage is too low ENG 456 Fuel Pressure in pump is not changing with operating conditions. Case Ih Code Reader TMF 134 Aux 3rd Raise solenoid failed open or short circuit.

Control - NO SIGNAL NH 3110 Monitoring of rail pressure relief valve - ABOVE NORMAL NH 3111 Monitoring of rail pressure relief valve - BELOW NORMAL NH 3112 Rail pressure Min ENG 211 Communications problem with Armrest, Instrumentation, or Transmission Controllers ENG 212 Oil Temperature Sensor Voltage is too high ENG 213 Oil Temperature Sensor Voltage is too low ENG 214 Oil Trans 2348 110 Clutch Mid Range solenoid open circuit or short to ground. http://windowsazure4j.org/new-holland/new-holland-error-code-02.html Hitch 1037 The ARU reports EDC Inching Down switch faulty or not available.

Hitch 1036 The ARU reports EDC Inching Up switch faulty or not available. ENG 2186 Supply Voltage to the accelerator pedal position sensor too low. ENG 429 Water in Fuel Sensor voltage is too low. Hitch 1026 Up/Down remote fender switch failure.

Trans 2072 Reverse switch input from the FNRP Pod is shorted to +12 Volts or the FNRP pod 5 Volt Reference. Trans 2873 Software is out of the calibration mode and the park brake request is still active. Trans 2055 No signal from wheel speed sensor. ENG 2117 Engine Coolant Level is low.

TMF 164 PTO shaft speed has not been detected within 3.6 seconds of being turned ON.