Home > New Holland > New Holland 8970 Error Codes

New Holland 8970 Error Codes

Contents

Trans 2071 Forward switch input from the FNRP Pod is shorted to ground or is open circuit. Engine 3273 Fuel Low Pressure Sensor -Signal Below Range Min. ENG 2372 Engine Fuel Filter clogged error ENG 2555 Intake Air Heater 1 Circuit Voltage too high. Trans 2358 Mid Clutch Solenoid is shorted to +12 Volts, Current sensed while driver is off. this contact form

What is your location? Ask Your Own Heavy Equipment Question Expert: dd85 replied7 years ago. ENG 352 5 Volt Sensor Supply voltage is too low ENG 378 Front Fueling current is too low ENG 379 Front fueling current is too high ENG 381 Error detected in there is also a solenoid valve housing and a transmission computer. TMF 62 Communications Lost with Performance Monitor Function TMF 63 Controller 8 volt reference is too high (above 8.8 volts). her latest blog

New Holland Tractor Trouble Codes

Trans 2361 The creeper clutch solenoid is shorted to +12 Volts, current sensed while the driver is off Trans 2362 Master Clutch Solenoid is shorted to +12 Volts, current sensed while TMF 7 Hitch Raise/Lower Solenoids Open or short to ground. via data bus command) ENG 319 Real Time Clock in controller has lost power ENG 328 Rear Pumping element is failed ENG 329 CAPS Pump has an overpumping failure ENG 338 ENG 2265 Electric Lift Pump for Engine Fuel Supply Voltage too high.

Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Engine 3019 Boost Pressure Sensor -Signal Above Range Max. Trans 2057 5 volt internal reference voltage too low. Case Puma Fault Codes via data bus command) ENG 319 Real Time Clock in controller has lost power ENG 328 Rear Pumping element is failed ENG 329 CAPS Pump has an overpumping failure ENG 338

Trans 2024 none of the Transmission clutches are calibrated. New Holland 8360 Fault Codes Error Code 2 - Engine coolant sensor fault. We are a company you can trust and have generous return policies. http://talk.newagtalk.com/forums/thread-view.asp?tid=484417&DisplayType=nested&setCookie=1 Trans 2071 Forward switch input from the FNRP Pod is shorted to ground or is open circuit.

ENG 429 Water in Fuel Sensor voltage is too low. Case Backhoe Fault Codes Engine 3012 Air Intake Temperature Sensor -(via CAN) No Signal Engine 3015 Fuel Temperature Signal -Signal Above Range Max. Add coolant fluid. ENG 234 Engine Speed has exceed the overspeed warning limit.

  • TRANS 75 Engine speed from Inst Controller does not match the speed signal from the alternator.
  • Credentials confirmed by a Fortune 500 verification firm.
  • ENG 147 Frequency Throttle Signal shorted high ENG 148 Frequency Throttle Signal shorted low ENG 151 Coolant Temperature level has exceeded the warning limit.
  • TMF 6 Hitch Lower Solenoid High Side Driver circuit short to 12 volts.
  • Trans 2048 Bottom of Clutch pedal switch or the bottom of clutch relay are short circuit Trans 2049 Trans Trans 2054 5 volt reference voltage too low.
  • Hold the transmission lever in the forward upshift position, numbers will appear on the shift lever display, ie 100, 120 121 122 ,, when the clutch pack is close to being
  • Moline Oliver Marketplace Classified Ads Photo Ads Tractor Parts Community Discussion Forums Project Journals Tractor Town Your Stories Show & Pull Guide Events Calendar Hauling Schedule Galleries Tractor Photos Implement
  • TMF 141 Aux 5th Raise Coil solenoid shorted to 12 volts.

New Holland 8360 Fault Codes

Hitch 1018 Hitch rockshaft position potentiometer open/short/misadjust or circuit failure. Engine 3045 Vehicle Speed Sensing -Signal Below Range Min. New Holland Tractor Trouble Codes TRANS 76 Engine speed from Eninge Controller does not match the speed signal from the alternator. New Holland Tm Fault Codes Move the 3 point lever fully forward, down into the lowest position, (there is a small notch for it to go down in) leave lever in this position for 2 seconds.

INST 12071 Communications Lost with Transmission Controller INST 12091 Communications Lost with Engine Controller INST 12101 Communications Lost with Tractor ECU (Gateway) Controller INST 12111 Communications Lost with Automatic Temperature Controller weblink TMF 135 Aux 4th Lower Coil solenoid shorted to 12 volts. the lower the number the better, 300 is MAX Now move the shift lever to netural, then to forward downshift, hold in that position as numbers start to climb and until Trans 2056 5 volt internal reference voltage too high. Case 580n Fault Codes

Ask Chris (aka - Moose) Your Own Question Chris (aka - Moose), Technician Category: Heavy Equipment Satisfied Customers: 112 Experience: 16 years of experience 2499435 Type Your Heavy Equipment Question Here... ENG 263 Fuel Temperature Sensor voltage is too high ENG 265 Fuel Temperature Sensor voltage is too low ENG 268 Fuel Pressure in pump is not changing with operating conditions. Engine 3025 Atmospheric Pressure Sensor -Signal Below Range Min. navigate here TMF 42 Engine speed must be set above 1600 rpm during calibration of lower valve.

INST 11011 Fuel Level Sensor voltage is too low (open circuit, short to ground) INST 12011 Communications Lost with Armrest Controller INST 12021 Communications Lost with Auxiliary Controller INST 12031 Communications New Holland Error Code 14101 there will also be a slight jump from 11th to 10th, this is normal. ENG 1257 Control Module Identification Input State Error.

If this fault is detected there is a bug in the software Trans 2874 The park brakes commanded on and gear is engaged and there is no park brake request from

Engine 3021 Boost Pressure Sensor -(via CAN) No Signal Engine 3022 Boost Pressure Sensor -Signal Not Plausible Engine 3023 Atmospheric Pressure Sensor -Signal Not Plausible Compared with Boost Pressure Engine 3024 Hitch 1027 Not implemented Hitch 1028 Travel Range potentiometer value received from CAN data bus indicates failure condition. ENZO Salve a tuttoil forum, vivo in Italia sono proprietario di un Ford New holland 240G (Ford 8.970) Non riesco a trovare i dischi Freno il codice sul disco 9821212, New Holland Skid Steer Error Codes Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co.

This will be the condition when a new controller is installed on the tractor. I paid a dealer almost 2500 to troubleshoot the problem and they found that the cab mounts had pinched down and ended up stressing the main electrical plug/harness going into the If they are near the 300 range, transmission repair maybe in the furture. his comment is here Engine 3035 Oil Temperature Sensor -Signal Below Range Min.

Hitch 1037 The ARU reports EDC Inching Down switch faulty or not available. TMF 24 Communications Lost with Instrumentation Controller TMF 25 Hitch Up/Down Switch failed in the Armrest controller TMF 26 Fender UP and DOWN switch failure or both switches simultaneously pressed TMF