Home > Error Code > Nh 1500 Error Code

Nh 1500 Error Code

Contents

Check settings of 3 Cassette FM Board Dip Switch (#2, #4, #6 On) 5. Set 1 Cassette 2. Reboot ATM 2. Replace Mainboard F0014 NVRAM Failure Fatal error, defective memory chip. http://windowsazure4j.org/error-code/ngm-error-code-5.html

Check Cash Dispenser EP ROM Version or specification 4003A00When more than 5 sheets of cash dispensing is required during a test_ Check command that CDU is received _ Check CDU EP Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error. D1706 Modem connection error Phone line connected to ATM will not support data communication. Check CS15A Sensor Cable3.

Hyosung Atm Error Codes

Check notesÕ status in the reject box 2. Check the shutter camÕs rotation.2. Check the wiring connections to the solenoid(s).

  • When "Low Cash Warning" is enabled in the Transaction Setup menu, this sensor will open when the cassette reaches (+/-) 75 bills.
  • Use an electrical parts contact cleaner to clean the terminals.
  • Check the Cutter module2.
  • Replace 2 cassette box when multiple errors occur. 400C200Cassette Jam during dispense operation(2 CST Encoder Error).1.Remove a jammed note in 2 Cassette. 2.Replace 2 cassette box when multiple errors occur. 400C33
  • Remove note from the CDU delivery path. 2.
  • Check the status of Near End sensor and its connector 2010800Receipt paper cuttimg error1.
  • If they do not the 20005 error will occur in which case the CDU will need to be reprogrammed to match the AP on the mainboard.
  • Check jam in 1 cassette and reload 4.
  • Close the lever of print head completely 2080200Receipt printer head overheated1.

Contact host processor D00A5 FS omitted (after total cash dispense amount in day close) Verify all programming. The only way to recover from this error is to reprogram the CDU data. Check CS21A Sensor Cable 3. Hyosung Epp Error Remove the remaining notes and foreign objects at the position of the CS4 sensor 2.

Initialize after removing the return path2. Hyosung Error Code 97999 Facebook Facebook LinkedInSearch Access © 2016: Access ATM, All Rights Reserved Access ATM, Inc. D170x Modem cannot support connection - excessive line noise (usually D1704/06) Phone line connected to ATM will not support Data-communication. Check the serial port or cable 9723017Send command time out error 9723019Polling down1.

Reboot ATM 2. Atm Error Codes List Verify that version of Mini-Bank Software matches host processor. Check settings of 3 Cassette FM Board Dip Switch (#2, #4, #6 On) 3. Contact host processor D00A9 ETX omitted (from configuration message) Verify all programming.

Hyosung Error Code 97999

Check the reject analysis to determine the cause of reject (reports menu). Check if printer head lever is properly close 2080900No sensing black mark (dark sensor)1. Hyosung Atm Error Codes D0020 Surcharge screen should have been displayed Code reported by host processor. Nautilus Hyosung Atm Error Codes Realign check sheets in the check cassette box. _ Reset number of check sheets after troubleshooting. 40092Reject error due to abnormal check interval skew during check dispense operation.1.

C0031 CDU Gate solenoid error The CDU did not respond to its solenoid function check. this content If no bills are present try using compressed air to clean the dispenser (a sensor may be blocked by dust). Remove the remaining notes at a sensor in front of the CST 2. Install after rearranging notes in cassette 4004A00Error of note jam (Separated rejection)1. Hyosung Error Code 97999(04)

Check if the CS31 and CS31B Sensor Cable are disconnected 4. If it still has the error the printer may require service. 20014 Thermal printer is overheated If this error occurs during the printing of a long journal, then allow the printer Try cleaning the cassette and dispenser. weblink Check notes in Reject Box2.

If error occurs when checking CS11A cable operation, replace a sensor. 3. Hyosung 1800 Error Codes You will need to physically go to the ATM location and manually reset the correct date with the Master Password. Exchange Sensor after abnormal operating CS7 Sensor 4003DDismount during rejecting separated cassette (Separated reject)1.

Remove notes jammed in CDU 3.

Reinstall software3. Open the vault and slide the dispenser back to access the exit gate area. Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error. Hyosung 2700 Error Codes Change CS5_1 Sensor 4003600Error of CS 2, CS13 sensor during initialization 4003700Error of 2 sheets detecting sensor(CS5_1/CS5_2) for dispensing1.

NOTE: Do not use metal objects to clear the jam. Check the status of sensor and its connector 2010600Command is received while doing self-test1. Initialize after executing the CDU Information Set(ÔPÕ) Command4. http://windowsazure4j.org/error-code/ngm-error-code-40.html Remove dust in CS1AB, CS15AB, CS31AB, CS41AB Sensor 4.

Check the abnormal communication cable.3. Clean CS1B and CS13 4002ACS11B and CS13 Dark detection during initializing or dispense reserved operationThe same as #40022 and #40028 error handling 4002A00Detecting CS1B, CS13 Dark 4002BCS1A, CS1B or CS13 sensor Check notes in 1Cassette2. D1800 No dial tone Verify that incoming phone line is plugged into "Line" rather than "Phone" on mainboard.

C006x Sensor failure Check for notes in the Cash Dispenser. Rearrange notes in cassette 3. Remove a jammed note in 3 Cassette.2. Replace hard disk drive 9712400Failed to delete file1.

Check the Cutter module 2. Remove a dust on the CS13 sensor 4005600Abnormal operation of the gate solenoid during dispense operation.1. Contact host processor D00A2 FS omitted (after available balance) Verify all programming. Check foreign objects in the main motor encoder slit5.

Read data of ÔRead Double Sensor Command 4003800Error in checking SRAM 4003900Gate operation sensor (CS3) error before initial recovery1. Try the printer reset switch. Replace the Cash Dispenser B/D 4005500Timeout due to noteÕs length error passed through the CS13 during dispense operation1. Check the reject analysis to determine the cause of reject (reports menu).

Check Index of notes4. Replenish receipt paper2.