Home > Error Code > Netbackup 7.0 Error Code 58

Netbackup 7.0 Error Code 58

Contents

Policy still set up as NDMP? get_long: (1) cannot read (byte 1) from network: Interrupted system call (4) bpcr_connect: bpcd protocol error - failed to read connected message. Launch the NetBackup Administration Console, connecting to the master server2. remove the disk volumes one at a time b. http://windowsazure4j.org/error-code/netbackup-error-code.html

The administration console is unavailable. enable granular recovery d. No Yes Veritas.com Support Veritas Open Exchange Login or Join Communities Information Governance Backup and Recovery Business Continuity Partners Inside Veritas Vision 2016 Developers Blogs Groups Vision 2016 Veritas.com Support Communities But the NDMP failures started before the licenses expired. https://www.veritas.com/support/en_US/article.TECH68832

Netbackup Error 59

Use caution when manually specifying sizes for the Initial and Maximum Cache Size, since these settings will be used regardless of volume size.Refer the NetBackup System Administrator's Guide for more information View solution in original post 0 Kudos Reply Accepted Solution! Anything in "All Log Entries" report or "Problems" report? telnet  13782That should generate a log entry as seen below showing the source host being recognized as a valid NB server. 16:52:46.077 [1160.5436] <2> bpcd main: offset to GMT 21600 16:52:46.077 [1160.5436] <2>

No Yes How can we make this article more helpful? bpmedia d. Do nslookup from media server to client and vice versa to make sure communication is working. Netbackup Port Numbers right-click the master and select Scan for updates d.

Backups fail with status code 58 after enabling Veritas Security Services (VxSS) and NetBackup Access Control (NBAC). Netbackup Error Code 58 In Windows Client bpbrm start_bpcd: cannot connect to nbu_client, Interrupted system call (4) bind_on_port_addr: bound to port 54702 check_authentication: no authentication required bpbrm kill_child_process: start bpbrm Exit: client backup EXIT STATUS 58: can't connect Replace the NIC itself on the affected client or server. If the snapshot source is not mounted but the mount point is present, NetBackup may try to take a snapshot of the directory preceding the directory that was specified as the

For NetBackup Snapshot Client, status code 13 may appear in the/usr/openv/netbackup/logs/bpbkarlog. Bptestbpcd: Exit Status = 25 Suggest you do general Michael_G_Ander Level 6 Certified ‎11-08-2014 01:11 AM Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content Suggest Go to Solution NDMP backups fail with code 58 rocker65 Level 4 ‎04-01-2011 08:00 AM Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend What should the administrator do to successfully restore data?

Netbackup Error Code 58 In Windows Client

Follow all steps within the VERITAS NetBackup Troubleshooting Guide or the NetBackup Troubleshooter within the Activity Monitor for this status code before continuing. 2. Showing results for  Search instead for  Do you mean  VOX : Backup and Recovery : NetBackup : Backups are failing with error code 58 in netbacku... Netbackup Error 59 What is the cause of this error? Netbackup Cannot Connect On Socket With this not selected, NetBackup automatically determines the best VSP cache file sizes.

A Prioritized storage unit group is configured with two BasicDisk storage units and one tape storage unit that is configured with three DLT tape drives. navigate here Trying to backup a Netapp with NDMP. Issue STATUS CODE 84: Backup jobs fail with a NetBackup Status Code 84 (media write error) and the system's device driver returns an I/O error while NetBackup is writing to removable A problem specific to NetBackup Snapshot Client (see recommended actions). Bptestbpcd

  • Troubleshooting procedures for Status 58 errors.7/6/2010file://H:\study\netbackup\Upload_site_done\done\New Folder\Can't connect to client- status 58.htm  Creating a bplist log on the client at verbose 5 should show the attempt to resolvethe master
  • From the media server run the command:# telnet 13782This should connect to the client and display a blank line.
  • Tape Summary 2.
  • The client sees the incoming connection from source IP address 10.82.105.254 ...16:52:46.077 [1160.5436] <2> logconnections: BPCD ACCEPT FROM 10.82.105.254.44554 TO 10.82.110.6.13782  16:52:46.077 [1160.5436] <2> bpcd main: setup_sockopts complete ...

Replace the faulty SCSI card. SunOS 5.8 Generic February 2000 [email protected]%last -1 anyuser pts/7 BUServer Thu Feb 21 12:33 still logged in [email protected]% [email protected]% cat /usr/openv/netbackup/bp.conf SERVER = client connect options 4. Check This Out a.

enable NetBackup File System (NBFS) b. Error Code 25 In Netbackup Go to Solution. If you use off-host backup, the disk that contains the client files must be a SCSI or Fibre Channel device.

DOWN'ing it"Resolution:This combination of errors can be caused by a faulty SCSI card.

Connecting to the client host properties from themaster server would prove the master server can access the client without any problems.So if using a storage unit on the master server you It could be as simple as ensuring that both hosts in question have the same configuration options for when to use VxSS.In the example above, re-adding the USE_VXSS = AUTOMATIC entry Then info for the ndmphost shows machine name which is correct, machinedescription which is empty as I don't have one configured, machineflags = 0, and machinenbutype = ndmp (2) I opened Netbackup Status 23 The majority of these situations are due to the TCP port(s) not being open through the firewall, daemon processes not running and listening on the destination host, the destination host being unable to resolve the IP address of

To reduce the number, reschedule some of them or reschedule the entire backup to a time when the file system is less active. Within the NetBackup Administration Console, expandHost Propertiesin the righthand pane 2.WithinHost Properties, clickMaster Serverand then the double-click the name of theMaster Serverin the right pane 3.Click on theClient Attributessection 4.If the In most cases, NetBackup will be able to create a large enough VSP cache file for backups if this is not selected.If errors still occur with this not selected, it is http://windowsazure4j.org/error-code/netbackup-7-1-error-code-23.html Symantec NetBackup times out trying to mount a volume for backup indicating error code 52.

Anything in "All Log Entries" report or "Problems" report? 0 Kudos Reply tpautoconf test's out rocker65 Level 4 ‎04-01-2011 11:03 AM Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Sorry, we couldn't post your feedback right now, please try again later.